Show simple item record

dc.contributor.advisorHutapea, Parsaoran
dc.creatorKonh, Bardia
dc.date.accessioned2020-10-27T15:13:58Z
dc.date.available2020-10-27T15:13:58Z
dc.date.issued2016
dc.identifier.other965642590
dc.identifier.urihttp://hdl.handle.net/20.500.12613/1653
dc.description.abstractBackground: Majority of cancer interventions today are performed percutaneously using needle-based procedures, i.e. through the skin and soft tissue. Needle insertion is known as one of the recent needle-based techniques that is used in several diagnostic and therapeutic medical procedures such as brachytherapy, thermal ablations and breast biopsy. The difficulty in most of these procedures is to attain a precise navigation through tissue reaching target locations. Insufficient accuracy using conventional surgical needles motivated researchers to provide actuation forces to the needle’s body for compensating the possible errors of surgeons/physicians. Therefore, active needles were proposed recently where actuation forces provided by shape memory alloys (SMAs) are utilized to assist the maneuverability and accuracy of surgical needles. This work also aims to introduce a novel needle insertion simulation to predict the deflection of a bevel tip needle inside the tissue. Development of a model to predict the behavior of the needle steering in the soft tissue has been always a point of interest as it could improve the performance of many percutaneous needle-based procedures. Methods: In this work first, the actuation capability of a single SMA wire was studied. The complex response of SMAs was investigated via a MATLAB implementation of the Brinson model and verified via experimental tests. The material characteristics of SMAs were simulated by defining multilinear elastic isothermal stress-strain curves. Rigorous experiments with SMA wires were performed to determine the material properties as well as to show the capability of the code to predict a stabilized SMA transformation behavior with sufficient accuracy. The isothermal stress-strain curves of SMAs were simulated and defined as a material model for the Finite Element Analysis of the active needle. In the second part of this work, a three-dimensional finite element (FE) model of the active steerable needle was developed to demonstrate the feasibility of using SMA wires as actuators to bend the surgical needle. In the FE model, birth and death method of defining boundary conditions, available in ANSYS, was used to achieve the pre-strain condition on SMA wire prior to actuation. This numerical model was validated with needle deflection experiments with developed prototypes of the active needle. The third part of this work describes the design optimization of the active using genetic algorithm aiming for its maximum flexibility. Design parameters influencing the steerability include the needle’s diameter, wire diameter, pre-strain, and its offset from the needle. A simplified model was developed to decrease the computation time in iterative analyses of the optimization algorithm. In the fourth part of this work a design of an active needling system was proposed where actuation forces of SMAs as well as shape memory polymers (SMPs) were incorporated. SMP elements provide two major additional advantages to the design: (i) recovery of the SMP’s plastic deformation by heating the element above its glass transition temperature, and (ii) achieving a higher needle deflection by having a softer stage of SMP at higher temperatures with less amount of actuation force. Finally, in the fifth and last part of this study, an Arbitrary-Lagrangian-Eulerian formulation in LS-DYNA software was used to model the solid-fluid interactions between the needle and tissue. A 150mm long needle was considered to bend within the tissue due to the interacting forces on its asymmetric bevel tip. Some additional assumptions were made to maintain a reasonable computational time, with no need of parallel processing, while having practical accuracies. Three experimental tests of needle steering in a soft phantom were performed to validate the simulation. Results: The finite element model of the active needle was first validated experimentally with developed prototypes. Several design parameters affecting the needle’s deflection such as the needle’s Young’s modulus, the SMA’s pre-strain and its offset from the neutral axis of the cannula were studied using the FE model. Then by the integration of the SMA characteristics with the automated optimization schemes an improved design of the active needle was obtained. Real-time experiments with different prototypes showed that the quickest response and the maximum deflection were achieved by the needle with two sections of actuation compared to a single section of actuation. Also the feasibility of providing actuation forces using both SMAs and SMPs for the surgical needle was demonstrated in this study. The needle insertion simulation was validated while observing less than 10% deviation between the estimated amount of needle deflection by the simulation and by the experiments. Using this model the effect of needle diameter and its bevel tip angle on the final shape of the needle was investigated. Conclusion: The numerical and experimental studies of this work showed that a highly maneuverable active needle can be made using the actuation of multiple SMA wires in series. To maneuver around the anatomical obstacles of the human body and reach the target location, thin sharp needles are recommended as they would create a smaller radius of curvature. The insertion model presented in this work is intended to be used as a base structure for path planning and training purposes for future studies.
dc.format.extent144 pages
dc.language.isoeng
dc.publisherTemple University. Libraries
dc.relation.ispartofTheses and Dissertations
dc.rightsIN COPYRIGHT- This Rights Statement can be used for an Item that is in copyright. Using this statement implies that the organization making this Item available has determined that the Item is in copyright and either is the rights-holder, has obtained permission from the rights-holder(s) to make their Work(s) available, or makes the Item available under an exception or limitation to copyright (including Fair Use) that entitles it to make the Item available.
dc.rights.urihttp://rightsstatements.org/vocab/InC/1.0/
dc.subjectEngineering, Mechanical
dc.subjectMaterials Science
dc.subjectActive Instruments
dc.subjectActive Surgical Needle
dc.subjectMedical Devices
dc.subjectNon-invasive Surgery
dc.subjectSmart and Advanced Materials
dc.titleSmart Surgical Needle Actuated by Shape Memory Alloys for Percutaneous Procedures
dc.typeText
dc.type.genreThesis/Dissertation
dc.contributor.committeememberYin, Jie
dc.contributor.committeememberSadeghipour, Keya
dc.contributor.committeememberElahinia, Mohammad H.
dc.contributor.committeememberOchia, Ruth Shada
dc.description.departmentMechanical Engineering
dc.relation.doihttp://dx.doi.org/10.34944/dspace/1635
dc.ada.noteFor Americans with Disabilities Act (ADA) accommodation, including help with reading this content, please contact scholarshare@temple.edu
dc.description.degreePh.D.
refterms.dateFOA2020-10-27T15:13:58Z


Files in this item

Thumbnail
Name:
Konh_temple_0225E_12509.pdf
Size:
3.173Mb
Format:
PDF

This item appears in the following Collection(s)

Show simple item record